# # Configuration file for loadable modules; used by modprobe and kerneld # ## Aliases - specify your hardware ################################## # Network Interface Card drivers #alias eth0 ne #options ne io=0x300 irq=12 #alias eth0 rtl8139 #alias eth0 8139too #alias eth0 3c59x #alias eth1 off #alias tr0 off #alias scsi_hostadapter ide-scsi #alias fb0 off # only used for Mylex or Compaq Raid as module #alias block-major-48 off #alias block-major-49 off #alias block-major-72 off #alias block-major-73 off # only needed for fifth and sixth IDE adaptor #alias block-major-56 off #alias block-major-57 off # mouse (for older busmice) #alias char-major-10 off # paralel_port: #alias parport_lowlevel parport_pc #options parport_pc io=0x378 irq=auto # If you have multiple parallel ports, specify them this way: # options parport_pc io=0x378,0x278 irq=7,auto # For parallel port devices, uncomment the following two lines and change # "frpw" to the protocol type you use # post-install paride insmod frpw # pre-remove paride rmmod frpw #***************************************************************************** # If you want to use the kernel sound drivers instead of OSS 3.8.1z (the # recommended solution) please put comment signs in front of the following # entries. Then choose one of the sample configurations below. Uncomment all # lines starting with 'alias', 'options' or 'pre-/post-install' within one # such configuration and modify the parameters according to your needs (e.g. # the ressources chosen for this device in /etc/isapnp.conf). For a lot of # ISA soundcards the Soundblaster driver is a good starting point. #***************************************************************************** # alias char-major-14 off # alias sound off # alias midi off #***************************************************************************** # module : ad1816.o AD1816 chip # # Supported cards : # # Terratec Base 1/64 # HP Kayak # Acer FX-3D # SY-1816 # Highscreen Sound-Boostar 32 Wave 3D # Highscreen Sound-Boostar 16 # # Documentation available in /usr/src/linux/Documentation/sound/AD1816 # and in /usr/src/linux/drivers/sound/ad1816.c . # # Possible configuration : # # alias char-major-14 ad1816 # post-install ad1816 modprobe "-k" opl3 # post-install ad1816 modprobe "-k" mpu401 # options ad1816 io=0x530 irq=5 dma=1 dma2=3 ad1816_clockfreq=33000 # options opl3 io=0x0388 # options mpu401 io=0x0330 irq=9 # #***************************************************************************** # module : ad1848.o AD1848/CS4231/CS4248 Chip # --> Windows Sound System (MSS/WSS) # # A variety of common ISA soundcards are # compatible with this family of chips. # # Documentation available in /usr/src/linux/drivers/sound/ad1848.c (search # for MODULE_PARM) and in /usr/src/linux/Documentation/sound/README.OSS . # Usually this module is used in conjunction with other higher level sound # modules. # # Possible configuration for stand-alone usage : # # alias char-major-14 ad1848 # options ad1848 io=0x530 irq=7 dma=0 dma2=3 # #***************************************************************************** # module : cs4232.o Crystal 423x chipsets # # Documentation available in /usr/src/linux/drivers/sound/cs4232.c (search # for MODULE_PARM) and in /usr/src/linux/Documentation/sound/CS4232 . This # chip is often used together with other sound hardware. # # Possible configuration for stand-alone usage : # # alias char-major-14 cs4232 # post-install cs4232 modprobe "-k" opl3 # options cs4232 io=0x534 irq=5 dma=1 dma2=0 mpuio=0x330 mpuirq=9 # options opl3 io=0x388 # #***************************************************************************** # module : es1370.o Ensoniq 1370 Chipsatz (--> PCI64/128) # # Supported cards : # # Creative Labs PCI64/128 # # Documentation availabke at /usr/src/linux/Documentation/sound/es1370 and # /usr/src/linux/drivers/sound/es1370.c . # # alias char-major-14 es1370 # options es1370 joystick=1 # #***************************************************************************** # module : es1371.o Creative Ensoniq 1371 Chipsatz (--> PCI64/128) # # Supported cards : # # Creative Labs PCI64/128 # # Documentation availabke at /usr/src/linux/Documentation/sound/es1371 and # /usr/src/linux/drivers/sound/es1371.c . # # alias char-major-14 es1371 # options es1371 joystick=0x200 # #***************************************************************************** # module : mad16.o MAD16 # # Possible configuration : # # alias char-major-14 mad16 # options sb mad16=1 # options mad16 io=0x530 irq=7 dma=0 dma16=1 # #***************************************************************************** # module : sb.o Soundblaster 16, SB Pro + Clones # Also needed for AWE32/64 # # Dcoumentation available in /usr/src/linux/Documentation/sound/Soundblaster # and in /usr/src/linux/drivers/sound/sb.c . # # Possible configuration : # #alias sound sb #alias char-major-14 sb # post-install sound /sbin/modprobe "-k" "adlib_card" #options sb io=0x220 irq=5 dma=1 dma16=5 mpu_io=0x330 # options adlib_card io=0x388 #alias midi awe_wave # #***************************************************************************** # module : trix.o MediaTrix AudioTrix Pro # # alias char-major-14 trix # pre-install trix modprobe "-k" # #***************************************************************************** # module : wavefront.o Turtle Beach Maui, Tropez, Tropez Plus # # Comment from /usr/src/linux/Documentation/sound/Wavefront : # (please read that file !) # "the wavefront options "io" and "irq" ***MUST*** match the "synthio" # and "synthirq" cs4232 options." # # Possible configuration : # # alias char-major-14 wavefront # alias synth0 wavefront # alias mixer0 cs4232 # alias audio0 cs4232 # pre-install wavefront modprobe "-k" "cs4232" # post-install wavefront modprobe "-k" "opl3" # options wavefront io=0x200 irq=9 # options cs4232 synthirq=9 synthio=0x200 io=0x530 irq=5 dma=1 dma2=0 # options opl3 io=0x388 # #***************************************************************************** #***************************************************************************** # Example configs for ALSA # You don't need to run isapnp with ALSA, it has full PnP support. # See /usr/share/doc/packages/alsa/README.SuSE #***************************************************************************** # # ALSA native device support and OSS emulation support. Uncomment these # lines to enable ALSA: # #alias sound-slot-0 snd-card-0 #alias sound-service-0-0 snd-mixer-oss #alias sound-service-0-1 snd-seq-oss #alias sound-service-0-3 snd-pcm-oss # alias sound-service-0-8 snd-seq-oss #alias sound-service-0-12 snd-pcm-oss # # Uncomment this line too, you can setup your ALSA device permissions here: # #options snd snd_major=116 snd_cards_limit=1 snd_device_mode=0666 snd_device_gid=17 snd_device_uid=0 # # ALSA Card examples: # # Creative SB16 PnP (ALSA will do isapnp itself per default): # # alias snd-card-0 snd-card-sb16 # options snd-card-sb16 snd_index=0 # # Creative SB Live! (ALSA will find it with the kernel's PCI support): # # alias snd-card-0 snd-card-emu10k1 # options snd-card-emu10k1 snd_index=0 # # An other Example: IBM ThinkPad 600E with an CS423x emulated by an CS4610/11 # In this case, the native PCI Sound is expected to not work, but some chips # like the CS4610/11 have a very good emulation for older ISA non-PNP cards # like the CS423x family. The CS4610/11 e.g. has an good emulation of the # CS4231/2 cards and the CS4239 card, the snd-card-cs4236 e.g. supports the # CS4239 emulation of the CS4610/11 in the IBM ThinkPad 600E: # # alias snd-card-0 snd-card-cs4236 # options snd-card-cs4236 snd_index=0 snd_port=0x530 snd_cport=0x538 snd_irq=5 snd_dma1=1 snd_dma2=0 snd_isapnp=0 # # You MUST suppy all required snd_port, snd_irq and snd_dma parameter AND # the snd_isapnp=0 option to the snd-card if the card is not shown by pnpdump, # otherwise the ALSA driver will try to do PnP and will not find your card. # # This is an example of an post-install you may want use: # # post-install snd amixer set Master 100% unmute;amixer set PCM 100% unmute; amixer set Aux,1 100% unmute # (Aux,1 is the CDROM line-in in this ThinkPad 600E) # # For more info about the powerful amixer look into "man amixer". # # This will open your mixer channels in case you did not store a mixer setup # for your card in /etc/asound.conf and you will have a default configuration. # To test your new setup, do: # # depmod -a # rcalsasound restart # # If the modules were loaded, you can check them with lsmod. # # Open and unmute the mixer channels, e.g. with alsamixer, gamix or your # OSS mixer (alsamixer: unmute the Master and PCM channels with ",." and # raise them with the up/down-arrow keys, man alsamixer explains all the keys) # # To play a sound sample run: # # aplay /usr/share/sounds/alsa/whistle.au # # For a list of supported soundcards look into # /usr/share/doc/packages/alsa/cards.txt # and browse the other files there and www.alsa-project.org # for more information. #***************************************************************************** ######################################################################## # Options; these are examples; uncommented and modify the lines you need ######################################################################## # options cdu31a cdu31a_port=0x340 cdu31a_irq=0 # options sbpcd sbpcd=0x230,1 # options aztcd aztcd=0x320 # options cm206 cm206=0x340,11 # options gscd gscd=0x340 # options mcd mcd=0x300,11 # options mcdx mcdx=0x300,11 # options optcd optcd=0x340 # options sjcd sjcd_base=0x340 # options sonycd535 sonycd535=0x340 # options isp16 isp16_cdrom_base=0x340 isp16_cdrom_irq=0 isp16_cdrom_dma=0 isp16_cdrom_type=Sanyo # Use this if you have two network cards ne: # options ne io=0x300,0x320 irq=5,7 # options tulip options=0 # options 3c59x options=0 # options 3c501 io=0x280 irq=5 # options 3c503 io=0x280 irq=5 xcvr=0 # options 3c505 io=0x300 irq=10 # options 3c507 io=0x300 irq=10 # options 3c509 irq=10 # options at1700 io=0x260 irq=10 # options smc-ultra io=0x200 irq=10 # options wd io=0x300 irq=10 # options smc9194 io=0x200 irq=10 ifport=0 # options e2100 io=0x300 irq=10 mem=0xd0000 xcvr=0 # options depca io=0x200 irq=7 # options ewrk3 io=0x300 irq=10 # options eexpress io=0x300 irq=10 # options hp-plus io=0x300 irq=10 # options hp io=0x300 irq=10 # options hp100 hp100_port=0x380 # options apricot io=0x300 irq=10 # options ac3200 io=0x300 irq=10 mem=0xd0000 # options de620 io=0x378 irq=7 bnc=1 # options ibmtr io=0xa20 # options arcnet io=0x300 irq=10 shmem=0xd0000 # options plip io=0x378 irq=7 # options eepro io=0x260 irq=10 mem=0x6000 # options eth16i io=0x2a0 irq=10 # options fmv18x io=0x220 irq=10 # options ni52 io=0x360 irq=9 memstart=0xd0000 memend=0xd4000 # options bttv pll=1 radio=0 card=0 # options tuner type=0 # options msp3400 once=1 simple=1 # post-install bttv /sbin/modprobe "-k" tuner; \ # /sbin/modprobe "-k" msp3400 #options cipcb cipe_maxdev=2 cipe_debug=0 # block dev aliases #alias block-major-22 off # w pliku alias.h jest ide-probe-mod #alias block-major-33 off # w pliku alias.h jest ide-probe-mod #alias block-major-34 off # w pliku alias.h jest ide-probe-mod # network block device #alias block-major-43 off #alias char-major-4 off # serial #alias char-major-10-135 off # rtc cannot be compiled as a module #alias char-major-15 off #alias char-major-29 off # fb alias char-major-43 off alias char-major-44 off alias char-major-45 off #alias char-major-81 bttv #alias char-major-83 vtx #options vtx quiet=1 #alias char-major-108 ppp_async # w alias.h jest ppp_generic #alias char-major-109 lvm # w alias.h jest lvm-mod # USB #alias char-major-195 NVdriver #alias tty-ldisc-3 ppp # w alias.h jest ppp_async #alias tty-ldisc-7 off ## alias ax0 mkiss #alias ax0 off ## alias sp0 6pack #alias sp0 off #alias net-pf-4 off # IPX #alias net-pf-5 off # appletalk #alias net-pf-6 netrom #alias net-pf-10 off # if you want to disable ipv6 #alias net-pf-11 rose # w alias.h jest ax25 #alias tap0 ethertap #alias tap1 ethertap #alias tap2 ethertap #alias tap3 ethertap #alias tap4 ethertap #alias tap5 ethertap #alias tap6 ethertap #alias tap7 ethertap #alias tap8 ethertap #alias tap9 ethertap #alias tap10 ethertap #alias tap11 ethertap #alias tap12 ethertap #alias tap13 ethertap #alias tap14 ethertap #alias tap15 ethertap